Rich, permanent color worked into the slab.
A bare gray slab reads as unfinished, no matter how well it was poured. Stained and colored concrete fixes that by working real, lasting color into the surface so the slab looks like part of the house instead of an afterthought. We do it two ways. Integral color goes into the mix before the pour, so the tone runs all the way through the slab. Stain goes onto an existing slab and reacts with or soaks into the surface to build a rich, variegated color that does not look painted on.
For Front Range homes and businesses, color is not just looks. A surface that pulls together with your stone, siding, and trim makes the whole property feel finished. And because our sun sits at altitude with heavy UV, the difference between a cheap dye that bleaches out in a few summers and a real stain or integral color that holds is something you notice every year. We pick the system to match the slab, the use, and the look you are after, then seal it so the color stays where it belongs.
Weld County jobs often need heavier pads for equipment and trucks. We size and reinforce them for the real loads. For stained & colored concrete, that local knowledge is exactly what protects your investment. We plan the base, drainage, reinforcement, and finish around the conditions on your Greeley property, not a generic detail.
We serve every part of Greeley and the surrounding area, including Promontory, West Greeley, Poudre River Ranch, Trails at Sheep Draw. Wherever you are in Weld County, the crew shows up with the same standard.
At roughly 4,658 feet, Greeley gets intense high-altitude sun and a freeze and thaw cycle that is hard on any concrete poured without care. For stained & colored, that means air-entrained mixes, deliberate curing, control joints cut on time, and a base prepared for the expansive clay under your property. It is the difference between work that holds for decades and work that starts failing by the first or second spring.
These are two different tools and they solve different problems. Integral color is mixed into the concrete before it leaves the truck, so the pigment runs through the entire slab. Chip it, scratch it, or wear it over decades and the color underneath matches the top. That makes it the better choice for a fresh pour you want to keep one consistent tone. Surface stain is for concrete that is already down. We clean and prep the slab, then apply an acid or water-based stain that reacts with or penetrates the surface to build depth and movement. Acid stains give you those mottled, stone-like tones that no two slabs share. Water-based stains open up a wider color range and more predictable results. We will tell you which fits your slab and your goal.
The fastest way to make new concrete look cheap is to pick a color off a chart and hope it works. We do it the other way around. Before we commit, we look at your stone, brick, siding, and trim, and we build the color to sit with them rather than fight them. A warm tan slab next to gray stone reads wrong, and you will see it every day. We also account for the fact that color looks different wet, cured, and sealed, and different again under our hard high-altitude light than it does under a showroom bulb. Where it helps, we put down a sample so you are choosing from something real on your own site, not guessing from a brochure.
This is the honest question, so here is the straight answer. It depends on the system and the sealer, and it depends a lot on our UV. A thin surface dye or a bargain stain will bleach and wear, especially on a sunny driveway or patio that bakes all summer at altitude. That is the look people are scared of, and it is real. We avoid it by using stains that bond into the surface and integral color that runs through the slab, then protecting the top with a quality sealer rated for sun. Integral color cannot wear off because it is the concrete itself. Stain holds well when it is sealed and the seal is kept up. Color is not a one-time, forget-it finish. Plan on resealing every few years and the surface stays rich. Skip it and any sealed color will dull over time.
Sealer is what keeps stained and colored concrete looking new, and it does double duty here. It deepens and protects the color, and it keeps water and de-icing salt out of the surface, which is exactly what drives the freeze damage and scaling you see on unprotected slabs through a Colorado winter. We seal new color as part of the job and tell you honestly when it is time to do it again. If you already have stained or colored concrete that has gone flat and tired, we can often bring it back. Depending on the surface, that means a fresh seal, a re-stain, or a new application of color over a cleaned slab. We will look at what you have and tell you whether a refresh makes sense or whether the surface is too far gone.
Every Greeley job starts with a free, written estimate and a structural engineer on staff for the work that needs one. Licensed, bonded, and insured, with finishes from a clean broom texture to stamped, colored, and sealed.
You always know what is happening and what it costs before we mix a single yard. Here is the path from first call to final walkthrough.
We visit the site, measure, check drainage and soil, and hand you a clear written quote. No charge, no pressure.
We set the grade, thickness, reinforcement, and finish. Structural work gets engineered and permitted.
Forms, rebar, and a clean pour. We screed, float, and finish to the texture you picked, then cut control joints.
You can walk it in 24 to 48 hours. We walk the job with you and explain how to care for it through the first winter.
Still unsure about something?
Call the crew at (303) 569-4046 and we will talk it through.
Get a free, no-obligation estimate from a crew that knows Colorado soil, Colorado weather, and how to finish concrete that lasts.
Accessibility
Adjust the site to fit how you read and browse. Your choices are saved on this device.